/~/~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\~\ || ********* ********** ********* || || * * * * * || || * * * * * || || ******** * * * * || || * * * * * || || * * * * * || || ******** @ ********** @ ********* @ || || eleet msg ctr: (509) 454-7338 Q's VMAIL || \_\_________________________________________________/_// /--S O C I E T Y--O F--D O O M--P R E S E N T S-------\\ \/\__________________________________________________/\/ SODATE: 010596 VER: 1.1Beta by QUEUE of 509 |/~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\| |\ ******THE BASIC STAMP ][ MULTI COLOURED BOX******/| \\_________________________________________________// / \ \ COMPLEETE ELEET HARD(CORE)WARE PLANZZZZZZZZZZZZZZ / \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ =\=\=\=\=\=\=\=\=\=\=\=\=\=\==\=\=\=\=\=\=\=\=\=\=\=\=\= 1st ORDER: SHOUT OUTS!!!!!! 2600,DEFCON,JERRY GARCIA,MITNICK,SPAM,DIALERZ,KGBUD The CRACKER, CAPTAIN CRUNCH, MS. PAC-MAN, INFORMATION SOCIETY ,GRANTS BEER,SEATTLE,LSD,AOL,SHROOMS,MTV,GRATEFUL DEAD EUGENE SHOWZ 93/94,HOPE, THE MOVIE HACKERS,WARGAMES,MACGYVER,KNIGHT RIDER,LANCE WALLY & PARALLAX............................ =/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/=/= 2nd ORDER: DISK-LAMER!!!!!!!!! WE,I,OR YOU, WILL NOT BE HELD LIABLE FOR THE FULL FRAUD POTENTIAL OF THE FOLLOWING DEVICE DESCRIBED HERE-IN, UNLESS IT IS USED FOR THAT PURPOSE! GOT THAT!!!!!?? =/=/=/=/=/=/=/=/=/=//=/=/=/=/=/=/=//====/=/=/=/=/=/=/=/=/=/ 3rd ORDER: A Large PIZZA WITH EVERYTHING ON IT EXCEPT SMELLY FISH!!!!!! --------------------------------------------------------------------- JUST WHAT IS THIS COLORED BOX THINGY!??? ;{ The Society of DOOM's MULTI COLORED BOX is a bi-product of the cold war and phone phreaking. It's main but not limited to purpose is , RIP-OFF MABELL. IT is a fully programmable/flexable/affordable Dual Tone MULTI-FREQUENCY Generator capable of generating any boxing inband signalling tones. The test software contains code to produce SILVER,RED,GREEN and BLUE BOX TONES. It's all based around the BASIC STAMP ][ put out by PARALLAX. This PIC based micro computer can be programmed in basic along with its special commands that generate 1 or 2 sinwaves at any frequency between 0 & 32000 hertz for any duration. The BS][ has 16 i/o lines and the SOD MCBOX only uses six of them. So It's a very expandable device. Another application or addition would be to add a touch tone decoder. The BS][ can also talk directly to an rs232 port though one or more of its I/O lines. Contained here are the plans for one of many applications of the BS][.... Have PHUN! DON'T GET BUSTED!! =/=/=/=/=/=/=/=/=//=/=/=/=/=//==//===/=/=/=/=/=//=/=/=/==/= THE 4th!!!!!!: THE BS][ PROGRAMMER =/=/=/=/=/PART 1 of 2 ( YOU GOTTA PROGRAM IT B4 YOU USE IT) The BASIC STAMP ][ made by PARALLAX can be purchased from DIGIKEY. THE BASIC STAMP][ or BS2 costs $49. It is a 20mhz microcomputer contained in a 24pin DIP (DUAL INLINE PLASTIC IC PACKAGE). It's PIC based and contains a 4kbyte eeprom. The STAMP2.EXE programming SOFTWARE can be ftped from the NET: ftp.parallaxinc.com (Also contained with this ZIP) The BASIC STAMP ][ programming software takes commands in a basic like language and compiles then into a tokenized PIC instruction set and uploads it to the BS2's 4k eprom non-volatile memory,power down won't erase it,unless reprogrammed. The interface cable is RS232 serial and connects directly between the PC COM PORT and pins 1-4 of the BS2. To run the programming software on comport1 type STAMP2 /1 at the DOS prompt. 2 for 2 etc. Before programming, the unit must also be powered. A 9volt battery will work well with + on pin 24 and - on pin 23. Here is a pinout for the programming cable. I suggest getting a 24 or 28 pin IC socket and soldering the wire from the serial port to the socket. I do not suggest soldering directly to the BS2. Always use a socket!! Even in the BOX!!!: PROGRAMMING CABLE: BS2 DB-9 OR DB-25 FEMALE SERIAL CONNECTOR SIGNAL 24pin DIP ================================================================= PIN 2-----PIN 3----------------------->DATA OUT(TX)----> 1 PIN 3-----PIN 2----------------------->DATA IN(RX)----> 2 PIN 4-----PIN 20---------------------->ATTENTION(ATN)--> 3 PIN 5-----PIN 7----------------------->SIGNAL GND(VSS)-> 5 + POSITIVE 9 VOLTS IN--------------------> 24 - NEGITIVE GROUND------------------------> 23 + 5volts instead of 9--------------------> 21 BASIC STAMP 2 PINOUT -------------------- notch at top sout or tx pin1 * \/ * pin24 or +9Volts(vcc) sin or rx pin2 * * pin23 or -ground(vss) atn pin3 * * pin22 reset low or - ground or vss pin4 * * pin21 vdd or +5v supply I/O line 0 or P0 pin5 * * pin20 P15 or I/O 15 I/O line 1 or P1 pin6 * * pin19 P14 or I/O 14 I/O line 2 or P2 pin7 * * pin18 P13 or I/O 13 I/O line 3 or P3 pin8 * * pin17 P12 or I/O 12 I/O line 4 or P4 pin9 * * pin16 P11 or I/O 11 I/O line 5 or P5 pin10* * pin15 P10 or I/O 10 I/O line 6 or P6 pin11* * pin14 P9 or I/O 9 I/O line 7 or P7 pin12* * pin13 P8 or I/O 8 ****** NOTES: PINS 24 & 21 can be used one at a time. The BASIC STAMP2 can be powered off either 9volts on pin24 OR! 5volts on pin 21. NOT BOTH!!! OR DAMAGE MAY OCCUR!!! THE PROGRAMMING CABLE ONLY USES PINS 1-4,23,24 OR 21 of the BASIC STAMP ][. DOWNLOADING: WITH THE STAMP2 software running and the cable connected to the SOCKETED BS2. (MAKE SURE IT'S NOT PLUGGED IN BACKWARDS). THE NOTCH IS UP. THE FIRST PIN LEFT OF THE NOTCH IS 1, THE PIN RIGHT OF THE NOTCH IS 24. PRESS ALT-L for load, SELECT SODCODE.BS2.. With POWER ON TO THE STAMP AND CABLE CONNECTED RIGHT HIT ALT-R for RUN or download and WALLLA!! THE STAMP is PROGRAMMED WITH THE MULTI COLORED BOX SOFTWARE. REMOVE THE STAMP and Put it back in its anti-static pad.. DONE WITH PARTS 1 of 2.. Save the programming cable or JIG for future programming and modification. BUILDING THE KEYPAD INTERFACE INTO THE BOX!!:: PART 2/2 SOD MULTI COLOURED BOX PINOUTS ------------------------------ pin24 9volts or pin 21 5volts pin23 ground/minus pin5 i/o 0 TONES OUT to speaker pin6 i/o 1 KEY PRESSED pin7 i/o 2 KEY DATA LSB BCD1 pin8 i/o 3 KEY DATA BCD2 pin9 i/0 4 KEY DATA BCD4 pin10 i/o 5 KEY DATA BCD8 You will need the following parts including the BS2: Disc: Order#: Supplier: Price: --------------------------------------------------------------------- PARALLAX BASIC STAMP][ STAMP2-ND DIGIKEY $49 16 KEY ENCODER IC MM74C922N-ND DIGIKEY $11.25 16 KEY KEYPAD REAR MOUNT GH5004-ND DIGIKEY $12.40 (2 PACK) .022uF Capacitors 272-1066 RADIOSHACK $00.69 4.7uF Electrolytic Capacitor 272-1012 RADIOSHACK $00.49 (2) 24 PIN IC Sockets ED3124-ND DIGIKEY $00.97 18 PIN IC Socket ED3118-ND DIGIKEY $00.73 General Purpose PC BOARD 276-149 RADIOSHACK $01.19 9 Volt battery clips RADIOSHACK 9 or 25 pin female serial connector RADIOSHACK Small 8ohm Speaker (Salvage from earphones/old radio etc.) FOUR CONDUCTOR DATA CABLE (ABOUT 4 FEET) 22GUAGE STRANDED HOOKUP/PHONE WIRE FOR ASSEMBLY OF CIRCUIT SOLDER AND 15-25 WATT SOLDING IRON OPTIONAL POWER SWITCH -------------------------------------------------------------------- CALL DIGIKEY AT 1-800-DIG-IKEY (1-800-344-4539) --------------------------------------------------------------------- FILES is SODMCB.ZIP The file MCBOX.TXT (THIS FILE) The file BS2JIG.ANS is a schematic of the programming jig. The file MCBOX.ANS is a schematic of the BOX The file SODCODE.BS2 is our test code for the BOX The file USER.TXT is a list a frequencies and menu fuctions for the test software. STAMP2.EXE is the PARALLAX programming software.